Sea-Bird Electronics SBE 38 Uživatelský manuál stáhnout pdf (Strana 111)

Manual revision 006 Appendix III: Command Summary SBE 19plus V2

111

CATEGORY COMMAND

DESCRIPTION

Output

Format

Setup

OutputFormat=x

x=0: output raw frequencies and voltages in Hex

(required if using Seasave or SBE Data Processing).

x=1: output converted data in Hex.

x=2: output raw frequencies and voltages in decimal.

x=3: output converted data in decimal.

x=4: output pressure and scan number in Hex.

X=5: output converted data in decimal, in XML.

OutputSal=x

x=Y

: Calculate and output salinity (psu). Only

applies if OutputFormat=3 or 5.

x=N: Do not.

OutputSV=x

x=Y: Calculate and output sound velocity (m/sec).

Only applies if OutputFormat=3 or 5.

x=N: Do not.

OutputUCSD=x

x=Y: Calculate and output density sigma-t (kg/m

battery voltage, and operating current (mA) with data

polled while logging. Only applies if

OutputFormat=3 or 5.

x=N: Do not.

Profiling

Mode Setup

(commands

after MP do

not affect

Moored mode

operation)

Set to Profiling mode.

NAvg=x

x= number of samples to average. 19plus V2 samples

at 4 Hz and averages NAvg samples. Default 1.

Must be even number (2, 4, etc.) if 19plus V2

includes optional Quartz pressure sensor.

MinCondFreq=x

x= minimum conductivity frequency (Hz) to enable

pump turn-on.

PumpDelay=x

x= time (seconds) to wait after minimum

conductivity frequency is reached before turning

pump on. Default 60 seconds.

AutoRun=x

x=Y: Automatically wake up and start logging when

external power is applied; stop logging when external

power is removed. Magnetic switch position has no

effect on logging.

x=N: Do not automatically start logging when

external power is applied.

IgnoreSwitch=x

x=Y: Ignore magnetic switch position for starting

or stopping logging. Use StartNow, StartLater, and

Stop to control logging.

x=N: Do not ignore magnetic switch position.

Moored Mode

Setup

(commands

after MM do

not affect

Profiling mode

operation)

Set to Moored mode.

SampleInterval=x

x= interval (seconds) between samples (10 - 14,400).

NCycles=x

number of measurements to take and average

every SampleInterval seconds. Default 1. Must be

even number (2, 4, etc.) if 19plus V2 includes

optional Quartz pressure sensor)

MooredPumpMode=x

x=0: No pump.

x=1: Run pump for 0.5 seconds before each sample.

x=2: Run pump during each sample.

DelayBeforeSampling=x

x= time (seconds) to wait after switching on external

voltages and RS-232 sensors before sampling

(0-600 seconds). Default 0 seconds.

MooredTxRealTime=x

x=Y: Output real-time data.

x=N: Do not.

Logging

StartNow

Start logging now.

StartDateTime=

mmddyyyyhhmmss

Delayed logging start: month, day, year, hour,

minute, second.

StartLater

Start logging at StartDateTime=.

Stop

Stop logging or stop waiting to start logging. Press

Enter key before sending Stop. Must stop logging

before uploading data. If in Profiling mode and

IgnoreSwitch=N, can also turn magnetic switch Off

to stop logging.

1 2 ... 106 107 108 109 110 111 112 113 114 115 116 ... 123 124

Komentáře k této Příručce

Žádné komentáře

Sea-Bird Electronics SBE 38 Uživatelský manuál Strana 111

Komentáře k této Příručce